Standing seam metal roof on a home

Metal roofing ยท Abilene, TX

Metal Roofing in Abilene, TX

Boatman Roofing and Construction installs and repairs metal roofs on homes, shops and business buildings in Abilene. Metal roofing in Abilene, TX holds up to hail and heat better than most other materials, but only when the install is done right. Most metal roof problems trace back to how the panels went on, not the metal itself.

Call [PHONE] for a free written estimate on metal roofing.

Free written estimates

Roofs, siding & windows

Help with hail claims

Why Metal Makes Sense Out Here

West Texas weather is hard on a roof, and metal handles more of it than shingles do. It sheds hail better, it doesn’t dry out and crack the way asphalt does under summer sun, and a well-installed metal roof commonly outlasts two shingle roofs. It costs more up front than shingles, and the gap matters most to owners who plan to stay in the house long enough to make it back.

Metal isn’t automatically the right call for every roof or every budget. If you’re weighing metal against shingles, ask for both priced on the same written estimate so you can compare them side by side.

Installer fitting ribbed panels for metal roofing in Abilene, TX

Panel Types We Install

Exposed-fastener panels

The ribbed panels you see on shops, barns and plenty of houses around Abilene. Lowest cost of the three. The screws show on the surface, and the screws are where most of the long-term upkeep is.

Standing seam

Fasteners are hidden under raised seams instead of driven through the face of the panel. Cleaner look, fewer exposed places to leak, higher cost than exposed-fastener.

Stone-coated steel

Looks closer to a shingle or tile roof from the ground, with steel underneath doing the work.

We’ll tell you plainly which option fits your roof and your budget when we inspect it.

What a Good Metal Roof Installation Looks Like

Metal roof installation in Abilene lives or dies on a handful of details that aren’t visible once the job is done. Here’s what we watch for on every install, and what you should ask about if you’re getting quotes from more than one roofer:

Laps face away from the wind

Panels overlap one another. On an exposed roof, that overlap needs to point away from the prevailing wind, or wind will work its way underneath it over time.

The first panel sets the line

Every panel after it follows the first one. Rush that first panel and the whole run drifts out of square by the far end.

The house probably isn’t square

Most aren’t, even new construction. A crew that knows what they’re doing decides which edge you’ll actually see from the ground or the street and keeps that edge straight, even if it means a slightly uneven cut somewhere you won’t notice.

Extra fasteners at the bottom edge

The eave is where wind tries to lift a roof first, so that edge gets more screws than the field of the roof.

Screws snug, not crushed

Each screw carries a rubber washer. Drive it too hard and the washer splits, which becomes a leak a few summers later once the rubber has had time to fail. Drive it too loose and it leaks right away.

Straight screw lines

On a steep roof, every row of screws is visible from the street. Crooked rows are usually a sign of rushed or careless work elsewhere too.

Roofing screw with its rubber washer for a metal roof

Metal Roof Repair

Metal roof repair in Abilene usually comes down to a short list of recurring issues:

  • Screws backed out or washers dried out and cracked in the sun
  • Panels lapped the wrong direction, letting wind-driven rain underneath
  • Flashing loose at pipes, walls, valleys or wall transitions
  • Trim lifted by wind at a gable end or ridge cap
  • Dents and chipped coating after a large hailstorm

Most of this is fixable without replacing the roof. We swap the failed screws, reseal or replace the flashing, and refasten lifted trim. If the panels themselves are sound, there’s usually no reason to tear into a whole metal roof over a handful of failed fasteners.

Metal Roofs and Hail

Metal holds up to hail better than most asphalt shingles, but large hail can still dent a panel, and dents are mostly cosmetic rather than something that causes a leak on their own. Here’s the catch worth knowing before a storm, not after one: some insurance policies exclude cosmetic damage from coverage, even on an otherwise valid hail claim. Read that section of your policy, and ask your insurance agent whether choosing metal changes your premium one way or the other before you decide.

If hail has hit your metal roof and you’re not sure whether the damage is cosmetic or structural, see our page on hail damage and insurance claims for how that inspection and claim process works.

Damaged roof edge and gutter on a metal roof after a storm
Roofer checking the pipe flashing on a metal commercial roof

Metal Over Shingles, or Tear Off?

Whether metal can go over your existing shingles depends on local code and the condition of the roof underneath. Tearing off first lets us check the deck for rot or soft spots before anything new goes down, which is why we recommend it in most cases even where a cover-up is technically allowed. We’ll tell you which approach fits your roof and explain why when we inspect it.

FAQ

Metal Roofing Questions

Is a metal roof noisy in the rain?

On a house, not much. With solid decking and attic insulation underneath, a metal roof sounds close to a shingle roof in the rain. An open shop or carport with bare panels and no insulation is where you actually hear it.

Does a metal roof attract lightning?

No. Lightning strikes the highest point of a structure regardless of what it’s made of, and metal doesn’t add risk. If anything, metal’s advantage is that it doesn’t burn.

Can metal go over my old shingles?

Sometimes, depending on local code and the shingle roof’s condition underneath. Tearing off lets the deck be checked first, which is why we usually recommend it. Ask your contractor which approach they recommend for your house and why.

How long does a metal roof last?

Longer than shingles. Roofers commonly quote 40 years or more for a metal roof, depending on the panel type, the coating and how well it was installed.

Why is my metal roof leaking at the screws?

Usually the rubber washers have dried out and cracked, or the screws were driven too tight or too loose when installed. Replacing the failed screws and washers often fixes the leak without any other work.

Does metal roofing cost more than shingles?

Yes, metal costs more up front than asphalt shingles. It tends to make the most sense for owners who plan to stay in the home long enough for the longer lifespan to offset the higher install cost.

Get a Metal Roof Estimate

For metal roofing in Abilene, TX, call [PHONE] or send us a message. If you’re comparing metal against shingles, ask for both priced on one estimate so you can see the real difference side by side.